Engineer's thesis — 1949

• Bacon, John William — An Investigation of Blowing as a Method of Increasing the Maximum Lift of a Double-Wedge Airfoil
• Baker, Joe Dee — The Design of a Combination Food Cutter for Home and Restaurant Use
• Benezra, Joseph Nissim — Supersonic Flow in a Two-Dimensional Asymmetric Channel
• Benitez, Louis Eugenio — Studies of Radiant Heat Transfer from Pure Gases
• Bevernick, Richard Alexander — The Effect of Reynolds Number on the Flow Field About a 70° Cone
• Billheimer, John S. — The Generalized Phase Behavior of Paraffin-Tetralin-Bitumen Systems
• Blenkush, Philip George — A Wind Tunnel Investigation of the Aerodynamic Characteristics of High-Lift Devices on Supersonic Wings at Low Subsonic Speed
• Bottenberg, William Robert — Effect of Reynolds Number on the Flow About a Finite Cone of 70 Degrees
• Brown, John R. — A Critical Study of Spin-Up Drag Loads on Aircraft Landing Gears
• Burke, James Donahue — Sounding Rocket Performances Analysis
• Chandler, Ralph Stewart — An Investigation of the Stresses and Deflections of Swept Plates
• Chu, Tao Hung — Determination of Buckling Loads by Frequency Measurements
• Clancy, Albert Harrison — Experimental Investigation of Pressure Drop in Helical Coils
• Cooley, James Siggins — Reversed Bending Fatigue Properties of 25 S-T, 75 S-T, and 76 S-T Aluminum Alloys
• Crate, James Harvey — The Design of a Commercial Coffee Maker
• Densmore, James Edward — Wind Tunnel Investigation of the Aerodynamic Characteristics of High Lift Devices on Supersonic Wings at Low Subsonic Speed
• Dhawan, Satish — On the Design and Use of a Flexible Nozzle for the GALCIT Transonic Wind Tunnel
• Dwire, Oliver Scott — A Study of Pressure Drop in Helical Coils
• Ford, Warren Woodrow — Design of a Six Component Internal Strain Gage Balance System
• Foster, Francis Cecil — Investigation and Design of a Portable Evaporative Cooler
• Francis, Donald Lowell — An Experimental Investigation of Blocking in a High-Speed, Closed Wind Tunnel Using the Wall Pressure Method
• Garrett, Joseph — Experimental Deflection Survey of Cantilever Sectors of Uniform Thickness
• Geldart, Lloyd Philip — Periodic Variations of the Gravitational Force. A Gravity Survey in the Monk Hill Area. Transmission of Shot Impulses in Shallow Water
• Gilkeson, Fillmore Bolling — An Investigation of the Stresses and Deflections of Swept Plates
• Goebel, Thomas Parker — An Investigation of the Deformation of a 3S-O Sheet Specimen During Tensile Failure
• Goff, Gordon Henry — Volumetric and Phase Behavior of Propane 1-Butene System
• Gompf, George Edward — Supersonic Nozzle Design for Viscous Fluids
• Hardy, Donald James — The Effect of Surface Roughness upon 25 ST Aluminum Alloy Subjected to Repeated Tensile Stresses Above the Proportional Limit
• Harmon, Leonard Edward — Stress, Distribution in Two Circular Cylinders Intersecting at Right Angles Under the Influence of Internal Pressure
• Henry, William Earl — Experimental Deflection Survey of Cantilever Sectors of Uniform Thickness
• Lamb, William Emerson — Fatigue Strength of Metal Sandwich Type Construction
• MacKinnon, Neil Allan — Flow Field Around a Finite Cone with Shock
• Mandelbrot, Benoit B. — Some Potential Problems Arising in the Theory of Axial Turbomachines
• Marx, Michael Ferdinand — Low Speed Wind Tunnel Investigation of High Lift Devices on a 65° Swept-Back Supersonic Wing of 3.44 Aspect Ratio
• McElligott, Richard Hardy — Investigation of Pressure Drop Through Helical Coils
• McIntosh, James Alexander — The Design of a Combination Projector and Viewer for Use with Colored Transparencies
• McKenney, John Dill — An Investigation of Flow Separation in an Overexpanded Supersonic Nozzle
• Monroe, Gerald Morgan — Higher Order Approximate Solutions for the Flow in Axial Turbomachines
• Muirhead, Vincent Uriel — Flow Field Around a Finite Cone with Shock
• Ogilvie, Douglas Clark — Correlation of Existing Design Information on Sandwich Construction
• Pinkerton, Charles C. — Experimental Determination of the Thermal Conductivity of Porous Copper
• Ringness, William Merritt — The Effect of Surface Roughness upon 25 ST Aluminum Alloy Subjected to Repeated Tensile Stresses Above the Proportional Limit
• Schurmeier, Harris McIntosh — An Investigation of the Interference Effects of a Sting Support System on the Pressure Distribution over a Body of Revolution
• Schwarz, Robert, Jr. — The Design of an Indoor Electric Barbecue Stove
• Shonerd, David Edwin — Winged Rocket Performance Analysis
• Teig, Vernon Ellwood — Stress Distribution in Two Intersecting Cylinders Under Pressure
• Thomas, John William — Low Speed Wind Tunnel Investigation of High Lift Devices on a 65° Swept-Back Supersonic Wing of 3.44 Aspect Ratio
• Waldron, Robert Edwards — Design of a Household Electric Ironing Machine
• Wallace, Richard Alfred — The Design of a Portable Pipe Threading Machine
• Weatherup, Robert Alexander — An Experimental Investigation of the Pressure Loss in Flow Through Helical Coils
• Wolf, Leo — The Development and Design of the "Visual Street Indicator": an Improved Means for Conveying Route Information to Passengers on Public Transportation